Look up the "T10 Angel Eye" in the search and pick the 90mm one to see other photos of what they did and how they wired the rings. Very nice.
Also, if you believe the reviewer comments...
Someone tested the current draws.
70mm ring: 100mA.
90mm ring (same LED count as the 80mm): 130mA.
Festoon is rated by the vendor at .28 watts or a little less than 250mA at 12V.
--- In GrizHFMinimill@yahoogroups.com, "Rob Potter" <rob@...> wrote:
>
> Paul,
>
>
>
> I got the 12VDC 12W power supply here
> http://www.elementalled.com/12v-adapter.html , removed the board from it,
> and hooked it up to the mill's 110V switch. I used 3M double-sided foam tape
> to fasten it in the mill's control box.
>
>
>
> The aux switch on the LED board is so that I can shut it off to use my laser
> center finder without powering down the whole mill. The switch itself came
> from Radio Shack.
>
>
>
> I got the rare earth magnets that hold the board to the mill head at Rockler
> woodworking. I used a connector in the power cable so that I can simply pop
> the board off if I ever need to clean it.
>
>
>
> The board was 3/32" acrylic from Home Depot that was left over from one of
> my wife's projects.
>
>
>
> Rob
>
>
>
>
>
> From: GrizHFMinimill@yahoogroups.com [mailto:GrizHFMinimill@yahoogroups.com]
> On Behalf Of paul@...
> Sent: Wednesday, December 28, 2011 6:36 AM
> To: GrizHFMinimill@yahoogroups.com
> Subject: [GrizHFMinimill] Re: Ring light measurements
>
>
>
>
>
> Rob
> Can you recommend the power supply you used on your setup. Like what I see
> in your pictures and would like to copy your setup
>
> Paul
>
> --- In GrizHFMinimill@yahoogroups.com
> <mailto:GrizHFMinimill%40yahoogroups.com> , "Rob Potter" <rob@> wrote:
> >
> > I've sent an email with attached pictures of my installation directly to
> > you, Rysiu.
> >
> >
> >
> > Rob Potter
> >
> > Portland, OR
> >
> >
> >
> > From: GrizHFMinimill@yahoogroups.com
> <mailto:GrizHFMinimill%40yahoogroups.com>
> [mailto:GrizHFMinimill@yahoogroups.com
> <mailto:GrizHFMinimill%40yahoogroups.com> ]
> > On Behalf Of rysium
> > Sent: Monday, December 26, 2011 7:38 AM
> > To: GrizHFMinimill@yahoogroups.com
> <mailto:GrizHFMinimill%40yahoogroups.com>
> > Subject: [GrizHFMinimill] Re: Ring light measurements
> >
> >
> >
> >
> >
> > Dd you have any pictures of your installation? I'm looking for some light
> > that will not extend beyond mill's head.
> >
> > In the meantime I got myself nice JANSJO lamp from IKEA
> > (http://www.ikea.com/us/en/catalog/products/10128734/). Great LED spot
> light
> > for little machine (lathe or mill) with 24" long flexible arm. Easy to
> mount
> > on the machine too (instead of using heavy foot screw the arm to machine).
> > For 10 bucks it's a steal.
> >
> > RysiuM
> >
> > --- In GrizHFMinimill@yahoogroups.com
> <mailto:GrizHFMinimill%40yahoogroups.com>
> > <mailto:GrizHFMinimill%40yahoogroups.com> , "Rob Potter" <rob@> wrote:
> > >
> > > As far as vendor sources, I was able to fit one of these 24-LED 80mm
> rings
> > > for $4.86
> > >
> > >
> >
> http://www.dealextreme.com/p/t10-24-led-white-light-car-angel-eye-80mm-diame
> > > ter-26001
> > >
> > >
> > >
> > > Around one of these 15-LED 60mm rings for $3.28
> > >
> > >
> >
> http://www.dealextreme.com/p/t10-15-led-white-light-car-angel-eye-60mm-diame
> > > ter-25513
> > >
> > >
> > >
> > > And put one of these 48-LED festoons for $7.96 behind the concentric
> rings
> > >
> > >
> >
> http://www.dealextreme.com/p/t10-ba9s-festoon-2-88w-12v-48-led-car-ceiling-d
> > > ome-white-light-bulb-18060
> > >
> > >
> > >
> > > Nothing extends out beneath the edges of the mill head, yielding a very
> > > clean installation.
> > >
> > >
> > >
> > > Rob Potter
> > >
> > > Portland, OR
> > >
> > >
> > >
> >
>
------------------------------------
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/GrizHFMinimill/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/GrizHFMinimill/join
(Yahoo! ID required)
<*> To change settings via email:
GrizHFMinimill-digest@yahoogroups.com
GrizHFMinimill-fullfeatured@yahoogroups.com
<*> To unsubscribe from this group, send an email to:
GrizHFMinimill-unsubscribe@yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/